Weekly Roundup #17 – New Maker Products

This week’s Weekly Roundup we have the #NexD1 #IMUtion #RhinoSmart #Airblock #Tsubasa #RetroEngine #MKRZero #FlipPin


Kickstarter

KickStarter is a bit quiet… … but there’s a robot!

IMUtion

WR-NMP17-01-640xThe IMUtion is a small module with onboard Bluetooth, ARM M4F MCU, 16M flash and a 9DOF IMU.

The development platform also contains WiFi, LCD and extra battery pack.

It’s yet another wireless motion sensor module that’s reasonably priced.

 

Electroacoustic Workstation

WR-NMP17-02-640xThis analog acoustic kit is similar to the MakeyMakey, but instead has a four input mixer for microphones, motors and piezos. It also has an AM/FM radio input, envelope follower and low frequency oscillator.

 

Bobbie 1S Robot.

WR-NMP17-03-640xOh good grief Bobbie is back again! Look at that!
Moving on…

 

Rhino Smart

WR-NMP17-04-640xIf you have a RhinoPrinter and suffer from filament jams then this might interest you.
The Rhino Smart will detect filament jams and pause the print job for you. It’s been through a number of revisions so looks like a solid product.

 

The NexD1

WR-NMP17-05-640xThe NexD1 promises to be a high end multi-material liquid inkjet 3D printer that can even print PCBs.

The claim is that you can print up to 6 different materials at the same time and has a great water soluble support material.

I can print down to 10micron accuracy at 8 inch cubed print bed. Has touch control and WiFi connectivity.

If you have a spare 4 grand then check this out.

 

Ant Union (StrongArm)

WR-NMP17-06-640xThe other end of the spectrum there’s the Ant Union StrongArm which is a regular 3D printer capable of printing large volume objects in a variety of materials with a layer resolution of 40 to 350 microns.


IndieGoGo

A couple of Kickstarters have found their way onto IndieGoGo.

Airblock

WR-NMP17-07-640xThe Airblock was in one of my previous roundups, which is a modular drone with components magnetically held together.

 

iResistors, iCapacitor&iLed

WR-NMP17-08-640xand iResistors which creates common SMD resistor, capacitor and LEDs into a breadboard friendly format.

 

PocketLab Voyager

WR-NMP17-09-640xPocketLab is yet another wireless sensor, but this one seems to have everything in it.

There’s two models:

One with rangefinder, 9DOF IMU, altitude, temperature, humidity, barometer, and Lux sensor and the other includes esoteric things like dew point and heat index.

Both are accessible via bluetooth.

 

Tsubasa V3

WR-NMP17-10-640xThe Tsubasa is interesting. It’s a small fixed wing drone weighing only 250g.

Why is this important? If you live in Italy and several other countries there’s a weight limit. Anything under 300 grams has some relaxed regulations.

Comes with solar panels giving you 15 minutes of air time and contains 2.4GHz radio, LiPos, GPS, AdaPilot board and mounts for a camera.

 

Firewall Router Fanless PC

WR-NMP17-11-640xThis one I included because a lot of my subscribers ask me about cheap fanless PCs with router capability.

Well here it is. Contains an Intel J1900 quad core CPU, WiFi, 4G SIM, HDMI, mSATA and also SATA, and 4 Gigabit ports. Supports up to 8G DDR3 and runs pretty much all the variants of Linux.

 

RetroEngine Sigma

WR-NMP17-12-640xAnother one that isn’t really a Maker product, but some of you might be interested in.
The RetroEngine Sigma is similar to the previous one, but designed for retro arcade and console gaming. Heck it even looks like a 80s console.
It runs the quad core AllWinner H3, 512M RAM, 2x USB, SD slot, WiFi, and HDMI.
Basically everything you need to get back into retro gaming.

 


Others

Arduino MKRZero

WR-NMP17-13-640xThe Arduino MKRZero is here! Hey another product called the Zero! What is it with that word that is so popular?

It’s very similar to AdaFruit’s Huzzah. Actually very similar but runs the Atmel SAMD21 MCU, LiPo battery support, RTC and a swag of GPIOs that are NOT 5v tolerant.


Tindie

Tindie? Only a few things.

X-8266

WR-NMP17-14-640xOver at Tindie there’s the X-8266 which is a small NodeMCU board that is designed to be stackable.

Comes with a number of add-ons like…

 

X-Battery Shield

WR-NMP17-15-640x… a battery shield…

 

X-DHT11

WR-NMP17-16-640x…and sensors and displays.

 

eDOT core

WR-NMP17-17-640xThe eDOT core is an ATmega 328 based board that contains a battery backed RTC. It’s classic through hole construction, but not that many boards have onboard RTC.


AdaFruit, Seeed, SparkFun, DFRobot, DigiKey

Grove – LoRa Radio 433MHz

WR-NMP17-18-640xOver at Seeed they have some Grove based LoRa modules which uses the RFM98 radio containing an ATmega168. This one transmits at 433MHz…

 

Grove – LoRa Radio 868MHz

WR-NMP17-19-640x… and there’s also an 868MHz version as well.

 

Pimoroni Rainbow HAT for Android Things

WR-NMP17-20-640xAdaFruit have their Rainbow Hat for androidthings which contains capacitive touch, temperature and pressure sensors, piezos and LEDs.

If you want to add some control mechanisms to your project then this is pretty good.

 

Adafruit Music Maker FeatherWing

WR-NMP17-21-640xNice! AdaFruit also have an audio player called the Music Maker FeatherWing which runs the VS1053B codec chip which can handle pretty much any audio format you can throw at it. Has SD slot and stereo audio out.

 

Flip-Pin

WR-NMP17-22-640xThe Flip-Pin is a great idea. I’m surprised no one thought of it before. It’s essentially a row of inverted pins that turns any breakout board into a standard IC package. Much lower profile than using header pins and comes in a plastic holder so you can solder those little buggers in without them going everywhere.

 

Mini GPS Shield

WR-NMP17-23-640xSparkFun have a cheap GPS shield that allows you to slot in a GP-735 GPS module an onboard SD slot…

 

LilyPad LilyMini ProtoSnap

WR-NMP17-24-640x… and also a credit card sized LilyPad starter kit that contains a LilyMini and a few sensors to get you started in e-textiles.

 

CY8CKIT-048 PSoC® Analog Coprocessor

WR-NMP17-25-640xNow if you’re really serious about your analog sensors, then this analog coprocessor board contains a PSoC signal processing engine and a flexible analog front-end. The intent is to give you a reliable platform in the cases where accuracy is critical.

 


The Cheap Side

Meanwhile in China there’s…

433MHZ 12V DC 15 Channel Wireless Remote Control Switch Receiver Module For Smart Home

WR-NMP17-26-640xA cheap way of adding some remote control to your home. A 15 channel relay, that doesn’t have any specs on the switching voltage, but is controlled by ASK radio module…

 

433MHZ DC9V 8-Channel Wireless Remote Control For Smart Home

WR-NMP17-27-640x… like this one.

 

UM220-III UM220 BD2 GPS Development Module Board With Antenna

WR-NMP17-28-640xThen there’s a cheap GPS module supporting the NMEA0188 protocol. running off 5 to 9 volts.

 

Customised Version WIFI Transceiver Wireless Module For DIY S-Forty-9er Telegraph Kit

WR-NMP17-29-640xAnd this one I originally thought was just a plain old ESP8266 module, which it is, but it’s designed to be attached to …

 

S-Class Forty-9er Telegraph Kit CW Transceiver 3W Shortwave Radio Telegraph 7.023M

WR-NMP17-30-640x… this. Which is a shortwave telegraph transceiver. Holy Cow! This is really cool. All you need is a 40m antenna and you can transmit up to several hundred miles. Hmmmm. Tempting!

 

ESP-32S-ALB – ESP32 Wifi Bluetooth Combo Module, Compatible with ESP-32S

WR-NMP17-31-640xIf you missed the boat with all the ESP32 modules, you can now pick up an ESP32 clone from AnalogLamb. Yup, that’s right we already have ESP32 clones around now, which is based off the Espressif module, but no idea how good it is.

 

61 Bit WS2812B 5050 RGB LED Driver Development Board

WR-NMP17-32-640xEleCrow are into LEDs it seems.

 

White 0.66in OLED Display Module 64×48 0.66″ Screen for Arduino AVR STM32

WR-NMP17-33-640xAnd ICstation are into OLEDs …

 

1pc 5730 SMD Pure White Waterproof Small LED Module 2Pcs LEDs 36x9mm For Lamp/Billboard

WR-NMP17-34-640x… and waterproof LEDs.

 


If you like this YouTube channel please subscribe by clicking the in-video button, or the little red “Subscribe” button in your browser or app. You can also get updates by subscribing to me on Facebook, Twitter, Google+, Pinterest, and also Tumblr.